John Deere F350M Front Mount Mower
Search Inventory    Search Products & Site
Easy, Affordable Financing Available NOW!
F350M  Front Mount Mower Model Photo

 

Features

Use front hitch for maximum productivity

Tractor hookup
8R Tractor front hitch 8R Tractor front hitch
8R Tractor front hitch 8R Tractor front hitch

The F350M Front-Mounted Mower is used to maximize the potential of the 7R or 8R Tractor equipped with a front power take-off (PTO) and front hitch. This 1000-rpm mower can be combined with the following 1000 rpm mower to increase productivity:

  • Twin rear-mounted mower

Unmatched productivity is gained with cutting widths up to 9.9 m (32.5 ft) in one pass along with a narrow transport width.

The A-frame adapter enables quick and easy installation of the F350M Front-Mounted Mower. The adapter attaches to the tractor’s front 3-point hitch and locks into the mating headstock that is part of the mower.

  • Enables easy attaching/detaching of front-mounted mower

Down stop chains are included for use with tractors, such as the 8R, without front hitch position sensing. A front chain support kit (RE327692) is required to connect the down stop chains on an 8R Tractor.

 

The 7R Tractors are equipped with position sensing that has the ability to establish front hitch set points from the CommandCenter™ controls. Position sensing will maintain the height of the hitch arms based on the set point.

 

The front chain support kit (RE327692) is not required for 7R Tractors, but damage to the front PTO driveshaft can occur if the front hitch positioning is not set correctly, or if the set point is manually overridden.

Hydraulic cylinders are used to raise and lower the cutting platform when crossing headlands.

  • Front tractor hitch is not used to raise and lower the cutting platform.
  • Uses single-acting selective control valve (SCV) to raise platform.
  • Lift cylinder operation must be independent of the front hitch operation.

High-speed rotary disc cutterbar for cutting in tough conditions

The 3.5-m (11.5-ft) wide cutterbar The 3.5-m (11.5-ft) wide cutterbar
Quick-change knives (QCK) technology Quick-change knives (QCK) technology

Large farms, machinery rings and contractors need high quality output, and ease of serviceability.

  • The cutterbars are fast mowing, with high quality work and reliable set-up.
  • Each disc is protected against heavy shocks with a shear point located on the disc drive.
  • All modules and intermediate gears are quickly and easily interchangeable.

To meet high quality output, the cutterbar is an oil-immersed, gear-driven cutting bed.

  • All discs are offering an orbital cutting diameter of 440 mm (17.3 in.).
  • With seven discs, the cutting width will be 3.1 m (10.2 ft). With eight discs, the cutting width will be 3.5 m (11.5 ft).
  • Disc speeds are 2986 rpm.

To meet serviceability, the cutting bed is lubricated for life:

  • No oil changes necessary.
  • Discs are fitted with quick change knives technology.
  • Cutting height is from 35 to 85 mm (1.4 to 3.3 in.).

Time needed to change a knife is below 15 seconds. It is an efficient way to gain up to 30 minutes of maintenance time on the mower conditioners.

 

Turnbuckle adjustment Turnbuckle adjustment

Cutting height is adjusted by changing the turnbuckle on the front hitch. Cutting range is from 35 mm to 85 mm (1.4 in. to 3.3 in.).

Key Specs

PTO speed 540 rpm
1000 rpm 1-3/8 in. PTO
1000 rpm 1-3/4 in. PTO
Powerline type
Standard hitch Clevis
Optional hitch Equal angle
Hydraulic pressure required 13,790 kPa
2,000 psi
Cutterbar - cutting width 2.4 m
8.1 ft
Number of disks/knifes 5
10
Transport width 2.4 m
8.1 ft

Power requirements

PTO speed 540 rpm
1000 rpm
540 rpm PTO 55-75 hp
41-56 kW
1000 rpm 1-3/8 in. PTO
1000 rpm 1-3/4 in. PTO
Powerline type

Tractor equipment

Tractor connection 21 spline
Standard hitch Clevis
Optional hitch Equal angle
Hydraulic pressure required 13,790 kPa
2,000 psi
Hydraulic connections

Cutterbar

Type John Deere
Cutting width 2.4 m
8.1 ft
Cutting height 2.8-9.8 cm
1.1-3.8 in.
Number of disks 5
Number of knives 10
Bolted knives
Disk speed 2,650 rpm
Knife tip speed 307 km/h
191 mph
Disk drive Gear
Lubrication Hy-Gard oil
Oil reservoir capacity 5.7 L
6 U.S. qt
Cutterbar oil check Combination check, drain plug
Cutterbar angle
Angle adjustment Manual or hydraulic
Angle range 2-8 degree (angle)
Cutterbar protection ShearHub
Adjustable gauge shoes Yes
Suspension system

Impeller conditioner

Width 140 cm
55.2 in.
Diameter 59.4 cm
23.4 in.
Tines type V-tines
Number of tines 33
Number of speeds Two
Drive 3-V powerband belt and sheaves
Conditioner hood
Wide spread

Rolls conditioner

Width
Diameter
Type of material
Design
Speed
Drive
Windrow width

Dimensions

Transport width 2.4 m
8.1 ft
Overall length
Transport length 6.2 m
20.6 ft
Weight, roll conditioner
Weight, impeller conditioner 2,027 kg
4,470 lb
Standard tires 11L-15 standard, 31x13.5L 15 optional
31x13.5L 15 optional

General

Are wrenches required for adjusting?

Additional information

Date collected August 24, 2020

Central Jersey Equipment is committed to your privacy. For more information view our Privacy Statement